Ößëå Canopus áðü üôé Ý÷ù äéáâÜóåé Ý÷åéò ôçí Spectrum DX7 Ý÷ù êáé åãþ ôçí ßäéá.
Ìðïñåßò íá ìå âïçèÞóåéò ãñÜöïíôáò ôé Ýêáíåò ìå ôï Throttle fail safe ãéá ôçí åíåñãïðïßçóç ôïõ Autopilot üôáí ÷Üóåé ï äÝêôçò ôçí åðéêïéíùíßá ìå ôïí ðïìðü.
Ðùò ôï Ýâáëåò 120% êáôÜ ôçí äéáäéêáóßá ôïõ áñ÷éêïý Bind áðü ôï travel rate adjust?
Êáé äåí êáôÜëáâá ðïõ ÷ñçóéìåýåé êáé ï ôñéðëüò äéáêüðôçò ðïõ áíáöÝñåôáé ðáñáðÜíù?
Åõ÷áñéóôþ
×ùñéò ôïí ôñéðëï äéáêïðôç äåí ìðïñåéò íá áëáæåéò ôïéò ïèïíåò óôçí ðôçóç ÐÁñáêáôù óïõ ðáñáèåôù åíá êïìáôé áðï ôï MANUAL Ôç¡RANFE video ÁÊÏËÏÕÈÇÓÅ ðéóôá ôçí äéáäéêáóéá ãéá íá ìðïñåéò íá êëåéíåéò ôïí ðïìðï êáé íá åíÅÑÃïðïéïçôáé ï áõôïìáôï ðéëïôïò..
In RVOSD PPM mode the OSD will look for pulses in Auxiliary input.
In RVOSD PCM mode the OSD will look for pulses in Auxiliary and Throttle inputs.
RVOSD can be adjusted to detect lost of RC link by two means, when it is set to PPM mode it analyze the servo pulses incoming on the auxiliary channel, if those pulses are not present or randomly changing then it knows the link was lost and take the appropriate actions based on menu item “Autopilot” on the autopilot submenu. When it is set to PCM mode it will do the same action on the auxiliary channel, but will also look at the throttle input for any servo period greater than the values set in the menu item “Set pcm FS point”.
If your receiver doesn’t have servo pulses post-processing, so it just output random or no pulses at all when the RC link it’s lost then you can use the PPM mode on RVOSD.
But if your receiver have servo pulses post-processing, so it can set failsafe on throttle channel you can use the PCM mode on RVOSD. And do the following instructions:
-Remove the propeller.
-With the inputs connected (auxiliary and throttle inputs must be connected, the others are optional) Make sure RVOSD it´s set to PPM mode in the menu item “Receiver mode”. If not, set it, save configuration and restart the OSD.
-Set your throttle stick to 105% of normal range.
-With the remote control go to the RVOSD menu.
-Save the throttle value in the menu item “Set pcm FS point".
-Change receiver mode to PCM.
-Go to the menu item “Save configuration” and execute (This way the changes on the menu will stay after you cycle power on the OSD). You will see the word “Done” blink on the screen.
-On the receiver, set throttle channel failsafe to 110%.
-Set throttle stick on your transmitter to normal range 0-100% (example: 0.90--1.9mS)
Now if you turn off your RC Transmitter, Throttle should go to 110%, this value is greater than the set pcm FS point set at 105% thus RVOSD will set RC link lost display action. With the Rc Transmitter ON again this value will go to normal range 0--100%. This value is less than the set pcm FS point witch it is set to 105%. Thus RVOSD will remove Rc Link lost action.
The OSD will never let the FS (110%) value goes out to the ESC.
Aeromodelling GR 
E-mail 
310.037 12.401 6.301 / : Clubdim
Ðåñéå÷üìåíá
Forum
Album
: 6301
