Ðáéäéá êáëçóðåñá êáé åõ÷áñéóôù ãéá ôéò áðáíôçóåéò!
Eâáëá ôñéðëï äéáêïðôç óôï aux êáé ïëá êáëá, áëëá óôï FBW mode ïôáí ôï âáæù äåí áêïõåé ôï ruder ìçðùò îåñåé êáíåéò ãéáôé?
ôï å÷ù óõíäåóåé óôï rvocd óôçí åéóïäï aileron êáé ç åéóïäïò ruder åéíáé êåíç, ãéá íá ìðïñù íá ôï ðåôáù ìå ôï äåîéï stick.
Öéëå canopus ðïëõ ùñáéï ôï ìïíôåëï óïõ êáé ôï âéíôåáêé åðéóçò.Ìðïñåéò íá ìïõ ðåéò ôé âáñïò óïõ å÷åé âãåé êáé ìå ôé ìðáôáñéåò?
Ôåëéêá ïé ir sensor ìðïñïõí íá ñõèìéóôïõí åí ðôçóç? áí íáé ðùò?
Áõôá ðñïò ôï ðáñïí, áõñéï èá êáíù ôçí ðñùôç ðôçóç êáé åëðéæù ïôáí åíåñãïðïéçóù ôï auto pilot íá ìçí áñ÷éóç ôï ìïíôåëï íá êáíåé ôéðïôá ôñåëá !!!
Èá ðïóôáñù âéíôåï ðáíôùò .
Êáëçíõ÷ôá!!!
Êáëùò çñèåò óôïí FPV êïóìï..
Áí äåí áêïõåé ôï Ruder sto FBW ìÜëëïí ðñåðåé íá êáíåéò áíáâáèìçóç ìå PICkit 2 USB programmer áëëá ðñïóï÷ç åäù ..ìðåò óôï
http://www.rangevideo.com/forum/showthread.php?t=383 êáé äéáâáóå ðñïóåêôéêá ðùò èá êáíåéò ôçí áíáâáèìçóç..Ôï âáñïò öéëå ìïõ åéíáé óôï êéëï êáé å÷ù ðåñéðïõ 45 ëåðôá ðôçóç ìå 2200 ìáç ìðáôáñéá..1 âáæù..ïé ir sensors ìðïñïõí íá calibraristoun åí ðôçóç ìïíï óôï íá åõèçãñáìéóôïõí ïé 2 ìðáñåò óôï êåíôñï ôçò ïèïíçò óïõ...ç äéáäéêáóéá íá êáíåéò ôï êáëéìðñáñéóìá óôï åäáöïò åéíáé êáëõôåñç..ìðáéíåéò óôï autopilot menou êáé... IR sensors equalization: Before starting it, make sure that you are in a location with unobstructed view to the sky. When this option is initialized, the OSD will display the steps and actions you need to do. First it will ask to get the plane leveled, during this stage the system it’s checking the Z sensors values and storing the biggest value detected. Second it will ask for keep the plane nose down, during this stage the system is checking the pitch aligned sensors maximum (if value is greater than 127) or minimum (if value is less than 127) and storing it to make the appropriate XY to Z on. After this the system should improve if you had sensors mismatch. If you are not satisfied with this correction and the AHI is working worst after the calibration (make sure to test this while flying). You can go to the menu “IR XY head position” and try to change it with your transmitter, It will not change because it is not allowed to be changed by the transmitter, but still will eliminate any change done by the AHI equalization.
Ôùñá ðñïóï÷ç óôéò ðñùôåò ðôçóåéò ..
ìçí åíåñãïðïéçò ôïí áõôïìáôï ðéëïôï óå ÷áìçëï õøïò êáëõôåñá óå ìåãáëï õøïò 200 ìåôñá åéíáé êáëá ãéáôé ÷áìçëá äåí èá ðñïëáâåéò íá åðáíáöåñåéò..âáëå êáëá óåñâï êáé UBEC ãéá íá ìçí å÷åéò ðñïâëçìá ôáóçò óôïí äåêôç óïõ..ìçí ðåôáò ìáêñõá óôçí áñ÷ç èá ÷áèåéò ..ôï speed control ìáêñõá áðï gps èá ôï ôñåëáíåé..
Åëðéæù íá óå âïçèçóá ..Óùêñáôçò
Aeromodelling GR 
E-mail 
310.037 12.401 6.301 / : Clubdim
Ðåñéå÷üìåíá
Forum
Album
: 6301
