Óõíäåóç çëå�ôñïëïãé�ùí

  Γ�áôáóôΓ�ìáôá
  Γ�åíôñéΓ�Γ� óåëΓ�äá
  Γ�ñèñá
  Links
  Γ“ýëëïãïé
  ΓƒΓ©Γ΅Γ΄Γ� áõôΓ� Γ§ óåëΓ�äá;

WWW Aeromodelling GR

Aeromodelling GR - IBabylon ThemeClassic YaBB SE ThemDelta TPNetBiz TPOmega TPSMF Default Theme

[akissofronas]

�áëçóðåñá óáò. ðñïóöáôá óå ìéá áëëáãç åëé�áò å�áëá ëáèïò íïõìåñï �áé ôï ìïíôåëï ðçñå öùôéá óôïí áåñá. �áç�å ìïôåñ speedcontrol �áé åé÷á ðôùóç ãéáôé å÷áóá ôá ðçäáëéá.
ç åñùôçóç ìïõ åéíáé ç åîçò .
 Γ°ΓΉΓ² ìðïñù Γ­Γ΅ óõíäåóù îå÷ùñéóôá ôïí ðïìðï ùóèå Γ³Γ¥ ðáñïìïéá ðåñéðôùóç Γ­Γ΅ ìðïñåóù Γ­Γ΅ Γ�áôåâù ôï ìïíôåëï?
 

[carapis]

  
  ΓƒΓ¥Γ©Γ΅ Γ³Γ―Γµ ÓôΓ�öáíå...
..., îå÷ùñéóôΓ� ìðáôáñéá ãéá ôïí Γ¤Γ�Γ�ôç-ðçäΓ�ëéá... ççç Γ±Γ�îå ìéá ìáôéΓ�  Γ³Γ΄Γ―Γ­ ðéï Γ�Γ�ôù óýíäåóìï..., ôï Γ�ΓΌΓ�Γ�éíï (+) îåóýíäåóå áðï ôï ESC...

1. The LiPo is connected directly to the power leads on the ESC.

2. The 3-wire lead from the ESC to the receiver has it's red wire (the +5v supply) disabled by pulling its pin out of the plug -- use the point of a hobby knife blade to pry up the little plastic tang that holds it in place, then pull the wire out and tie it back on itself with insulating tape so it can't touch anything.

3. The LiFe battery (2-cell probably) can then be connected directly or, better still, via an on/off switch, to any free channel in your receiver. If it's not specifically designed as an Rx pack you may need to crimp on a standard servo plug, taking care to ensure that the +ve wire (red) goes to the middle pin of the plug.

  
 https://forums.modelflying.co.uk/index.php?/topic/43229-using-separate-battery-for-servos-and-motor-and-how-to-connect-them-to-rx/

[Markhelis]

Ç äåýôåñç ëýóç å�íáé íá �÷åéò ôçí �äéá ìðáôáñ�á �áé íá â�ëåéò UBec åîùôåñé�ü,
âã�æïíôáò üðùò �áé óôçí ðñþôç ëýóç ôï + áðü ôï Esk!!!

[akissofronas]

Óáò åõ÷áñéóôù èá ôï ìåëåôçóù.
Ôùñá ôï öôéáîá �áé �ïëëçóå ç íôéæá áðï åíá óåñâï.
�ïõ öáéíåôáé èá ôï âáëù öùôéá ìïíïò ìïõ �áôù óôï õðïãåéï ïðùò åéíáé!