Lx f4u

  Γ�áôáóôΓ�ìáôá
  Γ�åíôñéΓ�Γ� óåëΓ�äá
  Γ�ñèñá
  Links
  Γ“ýëëïãïé
  ΓƒΓ©Γ΅Γ΄Γ� áõôΓ� Γ§ óåëΓ�äá;

WWW Aeromodelling GR

Aeromodelling GR - IBabylon ThemeClassic YaBB SE ThemDelta TPNetBiz TPOmega TPSMF Default Theme

[john_p51d]

¸÷ù ôåëåéþóåé ìå áõôü ôï Corsair ,�áé óôï íá ðñïãñáììáô�óù ôá Control throws .
Äõóôõ÷þò óôéò ïäçã�åò äåí õð�ñ÷ïõí ñõèì�óåéò. ¸÷ù âñåé óôï äéáäý�ôéï ôéò ðáñá��ôù:
CONTROL SURFACE THROWS
We recommend the following control surface throws. (Throws are measured at the widest part of the elevators, rudder and ailerons.)
ELEVATOR: 11/16" up, 5/8" down (High Rate)
1/2" up, 7/16" down (Low Rate)
RUDDER: 2-3/8" right, 2-3/8" left (High Rate)
1-3/8" right, 1-3/8" left (Low Rate)
AILERONS: 1/2" up, 1/2" down (High Rate)
3/8" up, 3/8" down (Low Rate)
FLAPS: At low point of middle flap,
1-3/8" down
NOTE: If your radio does not have �dual rates,�
then set up the control surfaces to move midway
between the recommended high and low rates.
Γ�Γ�ñåé Γ�Γ�ðïéïò Γ³Γ¥  mm  ðùò Γ¥Γ�íáé; Γ�õôü ðïõ ìå ìðåñäåýåé Γ¥Γ�íáé  ôï RUDDER: 2-3/8" right, 2-3/8" left (High Rate)
1-3/8" right, 1-3/8" left (Low Rate)

[john_p51d]

Foto

[falcon67]

Γ‚Γ�óåé ôïõ ôýðïõ  mm= in/0,039370 Γ�÷ïõìå:

Ãéá ôï Rudder:
2-3/8 =60,33 mm
1-3/8 =34,93 mm

�áë�ò ðô�óåéò

[john_p51d]

6cm ìå 3.4cm ôï âë�ðù ë�ãï äýó�ïëï!!!

[cptnassos]

Ãéá ðïéï ëüãï??

CONTROL SURFACE THROWS
We recommend the following control surface throws. (Throws are measured at the widest part of the elevators, rudder and ailerons.)

ELEVATOR: 11/16" (17.4mm) up, 5/8" (15.8mm) down (High Rate)
1/2" (12.7mm) up, 7/16" (11.1mm) down (Low Rate)

RUDDER: 2-3/8" (60.3mm) right, 2-3/8" (60.3mm) left (High Rate)
1-3/8" (34.9mm) right, 1-3/8" (34.9mm) left (Low Rate)

AILERONS: 1/2" (12.7mm) up, 1/2" (12.7mm) down (High Rate)
3/8" (9.5mm)  up, 3/8" (9.5mm) down (Low Rate)

FLAPS: At low point of middle flap,
1-3/8" (34.9mm) down

NOTE: If your radio does not have �dual rates,�
then set up the control surfaces to move midway
between the recommended high and low rates.

ÓÇ�ÅÉÙÓÇ: Å�í ç ôçëå�áôåõèçíóç óáò äåí �÷åé \"äéðë�ò ôéì�ò ñýèìéóçò\",
óôç óõí�÷åéá, ñõèì�óôå ôéò åðéö�íåéåò åë�ã÷ïõ ãéá íá ìåôá�éíçèå�ôå óôç ì�óç
ìåôáîý ôùí óõíéóôþìåíùí õøçëþí �áé ÷áìçëþí ôéìþí ��íçóçò.

[john_p51d]

�ðëá ôá servo äåí öô�íïõí áõô�ò ôéò áðïóô�óåéò óôï ruder.
Ôá õðüëïéðá ôá �÷ù �áé åãþ �ôóé õðïëïã�óåé

[cptnassos]

�áíå áëëáã� óôá horn ôùí servo ìå ìåãáëýôåñá (ìá�ñýôåñá).

https://www.aeromodelling.gr/ForumS/index.php?topic=56812.0

[john_p51d]

�á ôï �ïéô�îù áëë� ì�ëëïí äýó�ïëá èá âñù �ëëá íá ôáéñé�æïõí!

[cptnassos]

 

[kolotoympas]

Ãéá Γ¬Γ�ãéóôç Γ�Γ�íçóç åíüò ðéäáëéïõ ΓΆΓ�æåéò ôçí åîùôåñéΓ�Γ� ôñýðá óôï Servo Γ�áé áðü ôçí ìåñéΓ� ôïõ ruder ôçí åóùôåñéΓ�Γ�. 
ÄïΓ�Γ�ìáóå ôï.  Γ�áé Γ­Γ΅ ìçí öôΓ�óåéò ôï íïýìåñï ðïõ Γ«Γ�åé ôï Manual äåí ΓµΓ°Γ�ñ÷åé ðñüâëçìá.  Γ�ýôå ôï íïýìåñï ôïõ Low rates äåí öôΓ�íåéò?

[john_p51d]

�áé ð�åé ì�÷ñé 60mm, ôï âñ�ó�ù üìùò õðåñâïëé�ü.

[kolotoympas]

Γ�çí ôñåëáΓ�íåóáé Γ�áé 3 Γ¥Γ�íáé Γ�áëΓ�.