|
: Óõíäåóç çëåêôñïëïãéêùí : akissofronas , 11 2024, 15:09:43 êáëçóðåñá óáò. ðñïóöáôá óå ìéá áëëáãç åëéêáò åêáëá ëáèïò íïõìåñï êáé ôï ìïíôåëï ðçñå öùôéá óôïí áåñá. êáçêå ìïôåñ speedcontrol êáé åé÷á ðôùóç ãéáôé å÷áóá ôá ðçäáëéá.
ç åñùôçóç ìïõ åéíáé ç åîçò . ðùò ìðïñù íá óõíäåóù îå÷ùñéóôá ôïí ðïìðï ùóèå óå ðáñïìïéá ðåñéðôùóç íá ìðïñåóù íá êáôåâù ôï ìïíôåëï? : Áð: Óõíäåóç çëåêôñïëïãéêùí : carapis , 11 2024, 15:29:30 Ãåéá óïõ ÓôÝöáíå... ..., îå÷ùñéóôÞ ìðáôáñéá ãéá ôïí äÝêôç-ðçäÜëéá... ççç ñßîå ìéá ìáôéÜ óôïí ðéï êÜôù óýíäåóìï..., ôï êüêêéíï (+) îåóýíäåóå áðï ôï ESC... 1. The LiPo is connected directly to the power leads on the ESC. 2. The 3-wire lead from the ESC to the receiver has it's red wire (the +5v supply) disabled by pulling its pin out of the plug -- use the point of a hobby knife blade to pry up the little plastic tang that holds it in place, then pull the wire out and tie it back on itself with insulating tape so it can't touch anything. 3. The LiFe battery (2-cell probably) can then be connected directly or, better still, via an on/off switch, to any free channel in your receiver. If it's not specifically designed as an Rx pack you may need to crimp on a standard servo plug, taking care to ensure that the +ve wire (red) goes to the middle pin of the plug. https://forums.modelflying.co.uk/index.php?/topic/43229-using-separate-battery-for-servos-and-motor-and-how-to-connect-them-to-rx/ : Áð: Óõíäåóç çëåêôñïëïãéêùí : Markhelis , 11 2024, 20:06:12 Ç äåýôåñç ëýóç åßíáé íá Ý÷åéò ôçí ßäéá ìðáôáñßá êáé íá âÜëåéò UBec åîùôåñéêü,
âãÜæïíôáò üðùò êáé óôçí ðñþôç ëýóç ôï + áðü ôï Esk!!! : Áð: Óõíäåóç çëåêôñïëïãéêùí : akissofronas , 11 2024, 21:42:48 Óáò åõ÷áñéóôù èá ôï ìåëåôçóù.
Ôùñá ôï öôéáîá êáé êïëëçóå ç íôéæá áðï åíá óåñâï. Ìïõ öáéíåôáé èá ôï âáëù öùôéá ìïíïò ìïõ êáôù óôï õðïãåéï ïðùò åéíáé! ;D |